Parts

AT-001 · One piece

We confirm feasibility after reviewing the sample or drawing.

The bracket mounts a sensor to the vehicle and keeps it aimed at the point it needs to read.

AT-002 · One piece

We confirm feasibility after reviewing the sample or drawing.

The bracket holds the camera steady and keeps its field of view aligned with the area it needs to cover.

AT-003 · One piece

We confirm feasibility after reviewing the sample or drawing.

The mount keeps the GPS module in an accessible position and provides clearance for its cable.

AT-004 · One piece

We confirm feasibility after reviewing the sample or drawing.

The bezel finishes the display opening and covers the gap between the screen module and the surrounding panel.

AT-005 · One piece

We confirm feasibility after reviewing the sample or drawing.

The vent deflector directs air leaving the outlet toward the desired area of the cabin.

AT-006 · One piece

We confirm feasibility after reviewing the sample or drawing.

The clip snaps into its slot and holds trim against its backing without visible fasteners.

AT-007 · One piece

We confirm feasibility after reviewing the sample or drawing.

The retainer keeps a fitted component seated so it does not shift during use.

AT-008 · One piece

We confirm feasibility after reviewing the sample or drawing.

The plug closes an unused opening and covers the exposed edge of the panel.

AT-009 · One piece

We confirm feasibility after reviewing the sample or drawing.

A spacer sets the gap between parts, while a bushing centres a screw or shaft in its opening.

AT-010 · One piece

We confirm feasibility after reviewing the sample or drawing.

The enclosure houses the circuit board and provides defined locations for connectors and mounting points.

AT-011 · One piece

We confirm feasibility after reviewing the sample or drawing.

The holder keeps the cable on its intended route and away from edges and moving parts.

AT-012 · One piece

We confirm feasibility after reviewing the sample or drawing.

The adapter joins two differently shaped or sized ventilation openings where space is limited.

AT-013 · One piece

We confirm feasibility after reviewing the sample or drawing.

A stop limits travel at the end of a movement. A damper deforms on contact to soften the impact and reduce rattling.

AT-014 · One piece

We confirm feasibility after reviewing the sample or drawing.

The cover shields a small area from rubbing during use or installation.

AT-015 · One piece

We confirm feasibility after reviewing the sample or drawing.

The spare restores a specific assembly function when the original part is hard to source.

AT-016 · One piece

We confirm feasibility after reviewing the sample or drawing.

The service fixture holds a part in position so a workshop operation can be repeated consistently.

AT-017 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The long trim follows the dashboard contour and covers the joint between interior surfaces.

AT-018 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The long moulding finishes a continuous edge or seam along the interior.

AT-019 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The fascia frames controls, displays and vents while covering the gaps between them.

AT-020 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The trim finishes the centre console while leaving controls and storage openings accessible.

AT-021 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The trim covers the inner door surface and finishes openings for handles or controls.

AT-022 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The interior cover conceals auxiliary components and continues the surrounding trim surface.

AT-023 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The auxiliary duct carries air between separated cabin outlets along the available route.

AT-027 · One piece

We confirm feasibility after reviewing the sample or drawing.

The mount keeps the machine’s GPS receiver in a fixed position during field work.

AT-028 · One piece

We confirm feasibility after reviewing the sample or drawing.

The mount aims a camera or work light at the area the machine operator needs to see.

AT-029 · One piece

We confirm feasibility after reviewing the sample or drawing.

The housing supports the sensor while leaving its sensing face exposed where needed.

AT-030 · One piece

We confirm feasibility after reviewing the sample or drawing.

The case holds a controller and its connectors together at a defined mounting location on the machine.

AT-031 · One piece

We confirm feasibility after reviewing the sample or drawing.

The retainer keeps a hose on its intended route so it does not rub against the frame.

AT-032 · One piece

We confirm feasibility after reviewing the sample or drawing.

The fastening holds the wiring harness to the frame and makes its route easier to trace during service.

AT-033 · One piece

We confirm feasibility after reviewing the sample or drawing.

The spacer creates the required gap between an accessory and its mounting surface.

AT-034 · One piece

We confirm feasibility after reviewing the sample or drawing.

The stop limits the travel of a moving component or defines its resting position.

AT-035 · One piece

We confirm feasibility after reviewing the sample or drawing.

The handle provides a grip for manually moving or adjusting a mechanism.

AT-036 · One piece

We confirm feasibility after reviewing the sample or drawing.

The guide directs seed from the metering outlet into the next part of the feed path.

AT-037 · One piece

We confirm feasibility after reviewing the sample or drawing.

The short chute bridges the gap between transfer points and directs material toward the intended outlet.

AT-038 · One piece

We confirm feasibility after reviewing the sample or drawing.

As it turns, the disc separates small portions of material and transfers them to the metering outlet.

AT-039 · One piece

We confirm feasibility after reviewing the sample or drawing.

The repair template transfers hole positions or a profile onto the part being repaired.

AT-040 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The long chute guides material between separated points without carrying structural machine loads.

AT-041 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The cover encloses auxiliary equipment and defines access to its service points.

AT-042 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The panel finishes the tractor cab interior and covers seams or mounting openings.

AT-043 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The lid closes an auxiliary compartment and can be removed for inspection or cleaning.

AT-046 · One piece

We confirm feasibility after reviewing the sample or drawing.

The jig locates components against fixed references so their assembly position can be repeated.

AT-047 · One piece

We confirm feasibility after reviewing the sample or drawing.

The guide locates the drill at the intended points so the hole pattern can be repeated.

AT-048 · One piece

We confirm feasibility after reviewing the sample or drawing.

The gauge compares a feature or dimension with a defined inspection reference.

AT-049 · One piece

We confirm feasibility after reviewing the sample or drawing.

The fixture supports the component in its intended position while it is fastened.

AT-050 · One piece

We confirm feasibility after reviewing the sample or drawing.

The cradle follows the tool’s shape and gives it a dedicated place for storage.

AT-051 · One piece

We confirm feasibility after reviewing the sample or drawing.

The holder stabilises the workpiece during processing, inspection or internal transfer.

AT-052 · One piece

We confirm feasibility after reviewing the sample or drawing.

The housing locates the industrial sensor and defines access to its connector and sensing face.

AT-053 · One piece

We confirm feasibility after reviewing the sample or drawing.

The enclosure brings the controller board, connectors and mounting points into a single assembly.

AT-054 · One piece

We confirm feasibility after reviewing the sample or drawing.

The bracket attaches a component to the machine frame and sets its position relative to the equipment.

AT-055 · One piece

We confirm feasibility after reviewing the sample or drawing.

The spacer maintains a defined distance between surfaces and provides the clearance needed for assembly.

AT-056 · One piece

We confirm feasibility after reviewing the sample or drawing.

The guide routes wiring along the equipment and keeps it clear of the working area.

AT-057 · One piece

We confirm feasibility after reviewing the sample or drawing.

The nozzle or adapter changes the shape of the interface between a tool and its accessory.

AT-058 · One piece

We confirm feasibility after reviewing the sample or drawing.

The cap covers a connector, opening or small component during handling or storage.

AT-059 · One piece

We confirm feasibility after reviewing the sample or drawing.

Drive prototypes let engineers check fit, travel and alignment during a trial assembly.

AT-060 · One piece

We confirm feasibility after reviewing the sample or drawing.

The enclosure groups the parts of a small measurement bench and keeps its connections accessible.

AT-061 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The cover encloses the equipment and provides service openings without carrying its structural loads.

AT-062 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The enclosure brings test modules, connections and service access together in one housing.

AT-063 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The channel covers long wiring runs and allows access to a specific section for maintenance.

AT-064 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The tray separates tools, parts and consumables so each has a designated position.

AT-067 · One piece

We confirm feasibility after reviewing the sample or drawing.

Gripper fingers contact the workpiece, follow its contour and hold it while the robot moves it.

AT-068 · One piece

We confirm feasibility after reviewing the sample or drawing.

The contact tip defines where the gripper bears on the workpiece and distributes pressure at that point.

AT-069 · One piece

We confirm feasibility after reviewing the sample or drawing.

The linkage joins two pivots and transfers motion between them.

AT-070 · One piece

We confirm feasibility after reviewing the sample or drawing.

The mount holds a machine-vision camera at the position and angle needed to see the station.

AT-071 · One piece

We confirm feasibility after reviewing the sample or drawing.

The mount locates a sensor next to its detection zone and helps restore its position after adjustment.

AT-072 · One piece

We confirm feasibility after reviewing the sample or drawing.

The enclosure houses the automation controller and organises access to its wiring.

AT-073 · One piece

We confirm feasibility after reviewing the sample or drawing.

The platform provides a shared mounting surface for placing modules in repeatable positions.

AT-074 · One piece

We confirm feasibility after reviewing the sample or drawing.

The adapter helps check how an actuator fits an assembly with a different mounting interface.

AT-075 · One piece

We confirm feasibility after reviewing the sample or drawing.

The holder routes the harness along the station and keeps it outside the mechanisms’ path.

AT-076 · One piece

We confirm feasibility after reviewing the sample or drawing.

The sleeve spaces two surfaces apart to maintain the intended assembly clearance.

AT-077 · One piece

We confirm feasibility after reviewing the sample or drawing.

A moving prototype reveals travel and potential interference before the final part is defined.

AT-078 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The decorative shell finishes the robot’s exterior and conceals auxiliary components.

AT-079 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The non-structural panel closes off a face of a robotics test stand and can provide openings for controls or connections.

AT-082 · One piece

We confirm feasibility after reviewing the sample or drawing.

The small jig locates components against a common reference for ground assembly work.

AT-083 · One piece

We confirm feasibility after reviewing the sample or drawing.

The template compares a contour or feature position against a ground inspection reference.

AT-084 · One piece

We confirm feasibility after reviewing the sample or drawing.

The bracket mounts an electronics module to a ground bench or support unit.

AT-085 · One piece

We confirm feasibility after reviewing the sample or drawing.

The housing groups a test module and its connections so they can be handled as one unit.

AT-086 · One piece

We confirm feasibility after reviewing the sample or drawing.

The cover shields an opening or interface on ground equipment during handling or storage.

AT-087 · One piece

We confirm feasibility after reviewing the sample or drawing.

The holder routes test-bench wiring and keeps the operator’s working area clear.

AT-088 · One piece

We confirm feasibility after reviewing the sample or drawing.

Static model of one aircraft component for training and ground displays.

AT-089 · One piece

We confirm feasibility after reviewing the sample or drawing.

The inert enclosure mockup represents a small drone’s outer volume for appearance and access reviews at a workbench.

AT-090 · One piece

We confirm feasibility after reviewing the sample or drawing.

The prototype lets a team check sensor access and orientation on a ground bench.

AT-091 · One piece

We confirm feasibility after reviewing the sample or drawing.

The gauge checks a dimension or form against a known reference during ground inspection.

AT-092 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The non-structural enclosure covers ground test modules and organises access to their controls and connections.

AT-093 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The large display model reproduces the general outline of a structure so its arrangement can be explained on the ground.

AT-096 · One piece

We confirm feasibility after reviewing the sample or drawing.

The 1U mockup shows the outer volume of a single CubeSat unit for education and ground displays.

AT-097 · One piece

We confirm feasibility after reviewing the sample or drawing.

The 2U display model represents a two-unit body and helps explain how the form changes as the assembly gets longer.

AT-098 · One piece

We confirm feasibility after reviewing the sample or drawing.

The fixture holds small parts in defined positions when assembling demonstrators or bench equipment.

AT-099 · One piece

We confirm feasibility after reviewing the sample or drawing.

The template compares profiles or positions against a reference when inspecting a mockup or bench assembly.

AT-100 · One piece

We confirm feasibility after reviewing the sample or drawing.

The bracket holds accessories or instruments in a repeatable position on a laboratory bench.

AT-101 · One piece

We confirm feasibility after reviewing the sample or drawing.

The enclosure houses ground-support electronics while keeping connectors accessible.

AT-102 · One piece

We confirm feasibility after reviewing the sample or drawing.

The holder separates and routes bench cables so connections are easier to identify during a test.

AT-103 · One piece

We confirm feasibility after reviewing the sample or drawing.

The tabletop mockup illustrates a change from folded to open during a ground demonstration.

AT-104 · One piece

We confirm feasibility after reviewing the sample or drawing.

The transport cradle follows the part’s contour and holds it in place in transit.

AT-105 · One piece

We confirm feasibility after reviewing the sample or drawing.

The cap covers an exposed opening on a model or bench unit during handling.

AT-106 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The 3U display mockup shows an elongated three-unit volume for exhibitions or ground-based training.

AT-107 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The 6U display model shows a larger envelope for comparing formats in an exhibition or on a demonstration bench.

AT-108 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The enclosure organises space for instruments, connections and access points on a ground science bench.

AT-109 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The transport shell surrounds the equipment and shields its surfaces from incidental contact during handling.

AT-112 · One piece

We confirm feasibility after reviewing the sample or drawing.

The bracket keeps a navigation sensor oriented and leaves clearance for its cable.

AT-113 · One piece

We confirm feasibility after reviewing the sample or drawing.

The holder positions a camera or display where it can be viewed and adjusted during use.

AT-114 · One piece

We confirm feasibility after reviewing the sample or drawing.

The enclosure groups electronic modules and defines mounting points and cable entries.

AT-115 · One piece

We confirm feasibility after reviewing the sample or drawing.

Plugs close unused holes, while covers shield areas that need to be reopened.

AT-116 · One piece

We confirm feasibility after reviewing the sample or drawing.

The holder keeps a cable on its route and reduces rubbing against trim or cabinetry.

AT-117 · One piece

We confirm feasibility after reviewing the sample or drawing.

The adapter connects a duct to a differently shaped grille or outlet in a confined interior.

AT-118 · One piece

We confirm feasibility after reviewing the sample or drawing.

The handle provides a grip for opening a drawer, cupboard or access hatch.

AT-119 · One piece

We confirm feasibility after reviewing the sample or drawing.

The bezel finishes a small opening and covers the gap around the installed component.

AT-120 · One piece

We confirm feasibility after reviewing the sample or drawing.

The spacer sets the gap between a fitting and its supporting surface.

AT-121 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The long trim covers joints between linings and follows the cabin contour.

AT-122 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The panel covers a broad yacht interior surface and can incorporate openings for hatches or fittings.

AT-123 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The panel finishes the camper interior and covers the space behind the lining.

AT-124 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The cover encloses multiple auxiliary modules while leaving access for wiring and maintenance.

AT-125 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The duct moves air between separated compartments along the available route behind the lining.

AT-128 · One piece

We confirm feasibility after reviewing the sample or drawing.

A replacement clip restores the original fastening when a retainer is missing and its mounting slot can still be used.

AT-129 · One piece

We confirm feasibility after reviewing the sample or drawing.

A small replacement trim piece restores the local finish and covers an opening in an older vehicle’s interior.

AT-130 · One piece

We confirm feasibility after reviewing the sample or drawing.

A replacement housing restores a module’s enclosure while preserving the locations of its connections and fasteners.

AT-131 · One piece

We confirm feasibility after reviewing the sample or drawing.

The replacement bracket restores the mounting position of the component the broken bracket used to hold.

AT-132 · One piece

We confirm feasibility after reviewing the sample or drawing.

A small replacement part restores an auxiliary machine function such as guiding, spacing or retaining a component.

AT-133 · One piece

We confirm feasibility after reviewing the sample or drawing.

The spare restores an auxiliary function on farm equipment, such as holding a guide, cover or mount in place.

AT-134 · One piece

We confirm feasibility after reviewing the sample or drawing.

A replacement fitting reattaches an interior accessory to its original support in a boat or camper.

AT-135 · Segmented

We confirm feasibility after reviewing the sample or drawing.

Long replacement moulding restores a continuous trim line in an older vehicle’s interior.

AT-136 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The replacement panel covers a broad surface again while keeping required openings accessible.

AT-137 · Segmented

We confirm feasibility after reviewing the sample or drawing.

The replacement cover restores the outer enclosure while keeping service points accessible.